Homemade Solar Water Feature That Runs Day and Night

It is the dream of many people to create a gurgling water feature in the courtyard, let the smart sound of water flow interweave with the natural bird song, and add a unique charm to the home environment. Today, I will share with you a super creative DIY project - a homemade solar water feature that runs day and night, which is not only environmentally friendly and energy-saving, but also can become the focal landscape in the courtyard.

Materials Required

The materials required to make this solar water feature are rich and varied. First of all, the core component is the solar pump. This time, the brand Poposoap is used, which has high quality and excellent performance. Safety equipment is also required to ensure the safety of the production process. The concrete mixing barrel is used as the water storage base of the water feature, and the cutting board will be processed and covered on the top of the mixing barrel later. Don't forget to prepare the right drill bit to drill holes in the bottom of the cutting board and flower pots, and the copper pipe is used to guide the water flow. Plastic mesh and metal mesh can play a protective and decorative role, and the flower box can add a natural atmosphere to the water feature. In addition, two 6×8×8 cinder blocks are also indispensable, which will play an important role in fixing the equipment.

Production Begins

With the materials ready, the production work officially begins. The first step is to accurately measure the size of the cutting board. The measurement should be based on the size of the opening at the top of the mixing bucket to ensure that the cutting board can cover the opening tightly. After the measurement is completed, the cutting board is taken to the table saw and cut according to the measured size. After the cutting is completed, the installation test is carried out, and it is found that the cutting board fits the top of the mixing bucket very well and is a tight fit.

Drilling the Holes

Next, drill a hole in the center of the cutting board. The size of the drill hole should match the copper tube so that the copper tube can be firmly installed on the cutting board. Use the appropriate drill bit to ensure that the drilling direction is correct. After successfully completing the drilling, do the same operation at the bottom of the flower pot. After that, test the drill hole to ensure that the copper tube can smoothly pass through the holes at the bottom of the cutting board and the flower pot. This step of tight fit is crucial for the subsequent water flow guidance.

Placing the Mixing Bucket

After preparing the cutting board and flower pot, place the concrete mixing bucket in the hole dug in advance. Pay attention to adjusting the position when placing it, make sure that the mixing bucket is in a horizontal state, and then step on it with your feet to make it firmly fixed in the hole. Next, carefully place the heavy cinder blocks into the mixing bucket, placing two cinder blocks side by side to leave enough space for the water pump in the middle. After that, pour a small amount of concrete around the mixing bucket, which not only prevents weeds from growing when water overflows, but also makes the entire water feature more stable.

Applying the Sealant

Then, apply the sealant to the area where the cutting board is placed. Use the sealant to carefully apply the sealant to the area where the cutting board contacts the mixing bucket to form a good seal to prevent water leakage. During the application process, you need to continue to squeeze the sealant to evenly distribute it in the gap. After applying, smooth the excess sealant with your fingers to make the sealing effect better.

Installing the Water Pump and Battery Pack

After completing the above preparations, start installing the water pump and battery pack. The Poposoap water pump used this time comes with a battery pack, which is a highlight. During the day, the solar panel absorbs solar energy to power the water pump; at night or on cloudy days, the energy stored in the battery pack will continue to drive the water pump to run, so that the water feature will continue to work day and night. The pump is powerful, pumping 430 gallons of water per hour, with a maximum head of 8.5 feet, and the power can be adjusted by adjusting the knob. When installing, first place the pump in the middle of the cinder block, connect the water pipe, and secure it with a cable tie to prevent the water pipe from falling off. Then, connect the battery pack to the solar panel, and after the connection is completed, properly debug the entire device.

Preventing Mosquitoes

The last step is to use a net to prevent mosquitoes from entering. Covering the top of the water feature with a net can effectively block mosquitoes without affecting the beauty of the water feature. After installing the net, make the final adjustments to the entire device to ensure that the water pipe is properly positioned and the water can flow smoothly from the copper pipe, overflow on the cutting board and drip to the surrounding area. If you find that the device is not level, you can also make minor adjustments.

Completion

At this point, a homemade solar-powered water feature that runs day and night is complete. Watching the water flow and glittering in the sun, bringing vitality and vitality to the yard, is it a sense of accomplishment? If you are also interested in this project, you might as well try it and create a unique water feature for your yard.